These are the Support Forums for FSUIPC and related products.

These forums replace the old support forums which have been running for 20+ years. The old forums contain a wealth of information on all FSUIPC products, but are now no longer available.

Please note that you will need to Register and Login to post for support, and also to download attachments. You can view these forums without registering.

Support is also available via Discord. Please use the following invite link to join the FSUIPC Discord server:
https://discord.gg/zjwUTrxmmE

737/777 Parking Bra...
 
Notifications
Clear all

[Solved] 737/777 Parking Brake Release - FSUIPC Axis

Posts: 6
Registered
Topic starter
(@jsheck)
Joined: 4 days ago

Good day,

Finally went ahead and purchased FSUIPC so I could program many of the 737/777 controls to my HOTAS which I have been enjoying thoroughly. What an excellent program. I had noticed that my pedals when using the MSFS2024 axes would cause my pedals to go from 0% to 40-50% when I was applying 5% actual pedal (played around with sensitivities, deaszones etc, nothing could be improved). Through FSUIPC I was able to get this back to a nice smooth movement from 0-100%, no more MSFS2024 jump to 40-50% at 5% actual on the pedals. 

Here is where I ran into a single issue: Pushed back from the gate, engines on, ready to taxi on the ramp. When I push and hold the pedals (I have realistic engagement set) nothing happens. I push and hold for 8 seconds, nothing. I can see in FSUIPC that my pedals are reading their full travel from -16383 (ended up setting this to 0 instead of -16383) to 16384. Assigned a key to brakes on my keyboard, hold it for 3 seconds and the parking brake comes off without issue. I then pull the parking brake handle without applying brakes, doesn't engage, good. I apply 25%, then 50%, then 75% with my pedals, still doesn't engage...Exactly like it’s supposed to work. Push both pedals 100%, pull handle, parking brake engaged.

So the aircraft is reading my pedals correctly from 0-100%. I can also watch them as I press them.

My issue is I can't disengage the parking brake at 100% on both pedals for any amount of time. I even put BrakeReleaseThreshold=75 then 90 into the FSUIPC.ini to see if that would alleviate the issue to no avail.

Is there anything else I can try in the FSUIPC.ini? The aircraft is reading the brake inputs, I can engage the parking brake at 100% on both pedals as it should be so its reading 100% pedal engagement but something isn't triggering a disengage when they are held at 100% for any amount of time.

I also tried the FSUIPC option "send to FS as normal axis", didn't work either.

Is there a PMDG setting that I may be missing that triggers the parking brake to disengage at 100% that the FSUIPC isn’t triggering? The pedals are 100% depressed and FSUIPC confirms it. 

Thank you

 


13 Replies
Posts: 448
Moderator
(@fsuipc-support)
Joined: 1 year ago

Posted by: @jsheck
↑

Finally went ahead and purchased FSUIPC so I could program many of the 737/777 controls to my HOTAS which I have been enjoying thoroughly. What an excellent program. I had noticed that my pedals when using the MSFS2024 axes would cause my pedals to go from 0% to 40-50% when I was applying 5% actual pedal (played around with sensitivities, deaszones etc, nothing could be improved). Through FSUIPC I was able to get this back to a nice smooth movement from 0-100%, no more MSFS2024 jump to 40-50% at 5% actual on the pedals. 

Great - glad this worked for you!

Posted by: @jsheck
↑

My issue is I can't disengage the parking brake at 100% on both pedals for any amount of time.

Hmm, strange. I have checked this here in the PMDG 777-300 (MSFS2024) and the parking brake releases when I fully activate both the left/right brakes, so I am not sure what is happening. It also works in both Simple and Realistic modes. Did you try the Simple mode - do you get the same?

Could you activate logging for Events and Axes Controls please, and show me your FSUIPC7.log file showing this issue, i.e. load the aircraft and make sure the parking brake is set, then fully depress both brakes, hold for a second or two, then release. Then exit FSUIPC7 and show me / attach your FSUIPC7.log file as well as your FSUIPC7.ini file.
Note you can also see what is happening (i.e. the vents being received) in real0time by opening the logging console window (Log->Open Console). This is what I see in the log - notice the PARKING BRAKES control sent when the brakes are nearly fully depressed:

..
128297  AXIS: Cntrl= 66388 (0x00010354), Param= 14079 (0x000036ff) AXIS_RIGHT_BRAKE_SET
129328  AXIS: Cntrl= 66387 (0x00010353), Param= 14463 (0x0000387f) AXIS_LEFT_BRAKE_SET
129343  AXIS: Cntrl= 66388 (0x00010354), Param= 14463 (0x0000387f) AXIS_RIGHT_BRAKE_SET
129562  AXIS: Cntrl= 66387 (0x00010353), Param= 14719 (0x0000397f) AXIS_LEFT_BRAKE_SET
129562  AXIS: Cntrl= 66388 (0x00010354), Param= 14719 (0x0000397f) AXIS_RIGHT_BRAKE_SET
129609  EVENT: Cntrl= 65752 (0x000100d8), Param= 99 (0x00000063) PARKING_BRAKES

I don't think the BrakeReleaseThreshold ini parameter has any affect on this - seems to be something the aircraft handles - but I will also look into this a bit...maybe set this to 0 for now to disable.

I will also check here a further as when looking into this I am experiencing another strange issue - I cannot calibrate my parking brakes for some reason! I press 'Set' and nothing happens, which is very strange...

Regards,

John

P.S. Event logging may produce lots of unwanted log entries. To prevent these, you can add the following to your FSUIPC7.ini, under the [Profile.xxx] section (where xxx is the name of your 777 profile):

DontLogThese=67225,65709,65786


Reply
Posts: 448
Moderator
(@fsuipc-support)
Joined: 1 year ago

Please also check that you are using the latest release of the PMDG aircraft...for the 777-300ER, this is 2.04.147


Reply
Posts: 448
Moderator
(@fsuipc-support)
Joined: 1 year ago

Could you also please set logging for Extras - forgot to mention this.

After further tests, it seems that the FSUIPC calibration is affacting this. Mine worked as I could not calibrate (for some reason, to be investigated)... As a separate test, can you remove your calibration (click the 'Reset' button for both left and right toe brakes on the calibration page) and try without calibration. How does that work?

The BrakeReleaseThreshold ini parameter does have an affect, but only when the toe brakes are calibrated, which is why it wasn't having any affect here. I will continue to investigate...


Reply
Posts: 387
Admin
(@fsuipc)
Joined: 1 year ago

I've looked into this further now and it seems that the wrong controls are being used to release the brakes. When the parking brake is active, FSUIPC suppresses any assigned brake controls, to prevent any movement of the pedals in the VC, until the release threshold is reached, and when the release threshold is reached/passed it was using the FS BRAKES control to re-activate them. However, the standard BRAKES control does not work for the PMDG 777.

I have updated FSUIPC to handle the PMDG brakes (I hope!), so can you please try the attached version. To use this version with PMDG aircraft, you should add the following to the [JoystickCalibration.xxx] sections of your PMDG profiles (where xxx is/are the profile names), although you can also use these in the general [JoystickCalibration] section to apply to all aircraft:

BrakeReleaseThreshold=90
BrakeRelease=PMDG

Note that the BrakeReleaseThreshold needs to be around 90, as the values sent must be greater than the PMDG brake release threshold as defined in the aircraft.

You should also consider calibrating again: with your current calibration, you have no brakes at all for half of your axis range/movement. Thats fine if thats what you want, but better to use the full range and then calibrate with a slope if its too sensitive. But of course, you can use whatever is good for you!

No need to send the files I requested at the moment - just try this first and report back please:

Cheers,

John


Reply
Registered
(@jsheck)
Joined: 4 days ago

Posts: 6

@fsuipc Good afternoon John,

 

Thank you for the very prompt and thorough responses!

I am currently on an EDDF to CYVR flight with the PMDG 77W as we speak. When I land this evening I will give this a try.

I did find a temporary work around which worked quite well before you had a chance to respond. I assigned position 16384 to 16384 on each pedal to a key press and hold action follow by a key release action. Then I keyboard assigned "," for left brake and "." for right brake. The under parameters used 188+0 & 190+0 for the key press. So only when I pushed my pedal to the very end of the axis it would trigger the left and right tow brake keyboard command to release the parking brake. 

The way my pedals are designed, they go from -16383 to 0 then very smoothly from 0-16384, there is nothing between -16383 to 0. I had to reverse the axis as they were backwards.

The reason I moved my pedals from MSFS to FSUIPC was because in MSFS as soon as I applied 5% on the toe brakes the axis would jump to 40-50% pedal depression in the sim... They are the logitech pro flight rudder pedals. Been running these for a few years, they are fine in DCS, just seems to be an MSFS issue. With the 0-16384 in FSUIPC, they are extremely accurate, they progress following the real pedal very closely. I tried a +7, +3, -7 curve in FSUIPC but they are the most accurate and realistic with a 0 curve. I haven't been able to find any way to calibrate them in windows under the game controller area and logitech doesn't have software for it either. 

I also did originally try bumping the brake release threshold to 90 but that did not work. 

Will follow up in a few hours once I land and give it a try. 

I will try to add just those 2 lines to my FSUIPC.ini before I install the new .exe to see if its that simple of a fix.

Thank you again for all of your help!

Jordan

 

 


Reply
Page 1 / 3