This are the Support Forums for FSUIPC and related products.

These forums replace the old support forums which have been running for 20+ years. The old forums contain a wealth of information on all FSUIPC products, but are now no longer available.

Please note that you will need to Register and Login to post for support, and also to download attachments. You can view these forums without registering.

Support is also available via Discord. Please use the following invite link to join the FSUIPC Discord server:
https://discord.gg/zjwUTrxmmE

Notifications

Clear all

My FSUIPC7 with MS2024, PMDG B737-800 and FlightsimPM 737 Throttle

Morty · 2026-02-06T09:24:09Z

I have problems to get my TCA Yoke Boeing to work in MS2024, PMDG B737-800 and FlightsimPM 737 Throttle. Also my WinWing Orion Rudder Pedals will not work. I have been using tis earlier in MS2020 without any problems and FlightsimPM tells me that all the knobs shall be programmed in FSUIPC. The Throttle handles and Speed brake and Flaps handle also must be programmed in MS2024. All that was programmed but the Yoke and the pedals will not move for elevator, aileron, and the rudder pedals will not work when I setting up this like this. Any suggeston solve this? best reg Morten Aalberg

Page 2 / 2 Prev

Posts: 211

FSUIPC Support

Moderator

February 7, 2026 10:26 am

(@fsuipc-support)

Joined: 4 months ago

Why are you re-installing? Did you previously not register? How can you expect any assignments to work if you were not using a licensed version?

Posted by: @morty
↑
I have my registration code but it will not work on my innstall.

Please see documentation, section Invalid Key Problems in the Installation and Registration guide.

1 Reply

Morty

Registered

(@morty)

Joined: 2 weeks ago

Posts: 11

February 8, 2026 9:42 am

Reply to FSUIPC Support

When I install my FSUIPC7 it show my register code an I push the Register button

Posts: 11

Morty

Registered

Topic starter

February 8, 2026 9:38 am

(@morty)

Joined: 2 weeks ago

I was so stupid that I uninstall MS2020 and all of it. Should not have done that I know now.

Posts: 195

FSUIPC

Admin

February 8, 2026 10:24 am

(@fsuipc)

Joined: 7 months ago

After uninstalling and installing my FSUIPC7 with my reg code I can not see the choise for programing button

Please don't post images - they are useless and a waste of space. Always attach files (e.g. your FSUIPC7.log file).

If you do not see / have the 'Assignments' menu then you are running an unregistered / unlicensed version. Did you register your license correctly? i.e. did you enter your details and click the 'Register' button, and see a message confirming that the license is valid?

I don't know why you are having so many issues. You have been posting for days and don't yet even have FSUIPC7 installed correctly. This should take less than 5 minutes...

I suggest that you at least read the README.txt and Installation and Registration guide before posting again. Any issues, attach files, not images.

And PLEASE stop replying to comments that are several days old. These messages appear in the middle of this overlong conversation and are difficult to find. When trying to resolve an issue, add messages to the end of the conversation, i.e. click the red Add Reply button, and not the Reply button on each message. It would make this both easier to follow and easier to read, as everything then is in time order rather than all over the place...

John

Posts: 195

FSUIPC

Admin

February 8, 2026 10:26 am

(@fsuipc)

Joined: 7 months ago

Posted by: @morty
↑
When I install my FSUIPC7 it show my register code an I push the Register button

And does the code validate?

Check your FSUIPC7.log file for your registration details and validation status - Does it validate? Or attach your log file here so that I can see it please.

Page 2 / 2 Prev