ELITE King Air Throttle Quadrant for PMDG and other planes

Well now i Tested the work from the other day whit PMDG 737 and J41 and works (only throttles) It was tested whit other payware and worked to so far i found that Airbus X doesn´t work…

NOTE: about the 737NGX there is 1 limit A/T must ONLY be turned on when the AP should handle the throttles as it would stop the input from the Elite device, it was a necessary thing to get the best out of the NGX so the A/T doesn’t disconnect and might give some unwanted behaviour…

This is a good news for customers whit the ELITE King Air Throttle Quadrant…as it opens the options to be used whit more than Default planes as so far we seen problems when A/T had to be used.

ok first insert the lua file to the modules folder then open the fsuipc.ini file and add:

this is for it to run with all planes…

If it is the first time and you don’t have other lua to run whit any planes then add this as the last line:

[Auto]
1=Lua throttles

If you already have the [Auto] section then add: X=Lua throttles – change X to match the next number after the last one you have.

If you only want it to operate for a specific aircraft or profile use [Auto.<name>] instead… and remember to look for ShortAircraftNameOk and changes No to Yes …

—————————————————————————————————————————————————————————————————————————————————————

now we only need the calibration and i give you here the option for all planes:

go look for: [JoystickCalibration] where you go there look for Throttle1=<numbers> and Throttle2=<numbers> if you have them just copy pasted the lines below, if they isent there just add them at the last line.

Throttle1=-4096,-512,512,16380
Throttle2=-4096,-512,512,16380

when done it might look like this:

[JoystickCalibration]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=66731
RudderTrimControl=66732
CowlFlaps1Control=66162
CowlFlaps2Control=66163
CowlFlaps3Control=66164
CowlFlaps4Control=66165
SteeringTillerControl=0
MaxSteerSpeed=60
Throttle1=-4096,-512,512,16380
Throttle2=-4096,-512,512,16380

Thats it have a nice flight….

———————————————————————————————————————————————————————————————————————————————

Here is a small update i had to make in order to get the hardware to work whit planes that have 3 or 4 engins i had to include that aswell as i just update it anyway

as a small note in oder to control all 3 eng at once i had to make a changes so you might have to cheat the sim to think we had 4 eng that way leaver 1 controls eng 1 and 2 and leaver 2 eng 3+4. its sad that there isent a option for that under 3 eng only 4 so a edit of the aircraft.cfg is nessersary. 3 would work but odd as you know the lever ranges are different so its not posible to get eng 3 in full reverse so thats why i edit it´s just a small tip.. as all the file here does is to get A/T working.. at any time and configuaration you chose

Best regards Lars N.

[Originally contributed in old SimMarket support forums by Lars N / user KAPTEJNLN]